Products
2,497 Brands 483 Categories All Departments
Burris AR Tactical Mount 1/2 inch Picatinny Riser
$15.99 $22.00 Save 27%
Browse by Rating
(16 reviews)
Share your Thoughts! Write a Review
Most Helpful Positive Review Rock Solid Riser Block
Nice fit and sturdy. Fits nice on my AR-15 flat top. I've shot hundreds of...
Read More...
Most Helpful Negative Review Burris AR Tactical Mounts 1/2" Picatinny Riser
Very poor fit to a standard picatinny rail. Loose no matter how much its ti...
Read More...
Sort by
Show
Page
Back
Next

Screws Too Small for Picatinny Rail

by Steel, from United States, MI Written on September 21, 2014
While the product itself seems well built, the screws are too small in diameter for a standard Picatinny rail, thus rendering the mount loose on the rail. I've tried mounting these risers on more than one AR-type rifle which has a standard Picatinny rail (e.g., flat top), and the same problem occurs on each rifle.

This product is badly designed and needs to be redone from the ground up....
Pros:
  • Well-Made
Cons:
  • Bad design
Would recommend: No
0 of 0 found the following review helpful.
Was it helpful to you? Yes / No

Burris mount

by Legacy Reviewer, Verified Owner Written on May 1, 2013
Does not fit Daniel defense V5 rail system as the screws are to small to make a taught fit of the rail.
Pros: well made
Cons: screws are to small for Daniel defense V5 rail system...
Would recommend: Yes
0 of 0 found the following review helpful.
Was it helpful to you? Yes / No

great fit

by Legacy Reviewer, from United States, WA Written on March 25, 2013
Bought this riser to go under a Burris FastFireIII, and it is the perfect length and height to make the FF3 the primary sight on my shotgun. Works great.
Pros: clamps well on out of spec rail
Cons: none...
Would recommend: Yes
0 of 0 found the following review helpful.
Was it helpful to you? Yes / No

Burris AR Tactical Mounts 1/2" Picatinny Riser

by Legacy Reviewer, Verified Owner from United States, MI Written on March 25, 2013
Very poor fit to a standard picatinny rail. Loose no matter how much its tightened.Paid more for this than same part at local stores.Not real happy with it....
Would recommend: No
2 of 2 found the following review helpful.
Was it helpful to you? Yes / No

Does not fit standard rails - screws are too small!

by Legacy Reviewer, Verified Owner from United States, WA Written on March 19, 2013
Wish I would have read the other reviews a little closer...product returned for aformentioned reasons.
Pros: looked like a quality build
Cons: does not fit standard picatinny rails...
Would recommend: No
2 of 2 found the following review helpful.
Was it helpful to you? Yes / No

Yeah, they worked.

by Legacy Reviewer, Verified Owner from United States, OK Written on May 31, 2012
Pretty simple, they raised the scope up 1/2 inch.
Pros: They raised my scope up 1/2 inch.
Cons: none...
Would recommend: Yes
1 of 1 found the following review helpful.
Was it helpful to you? Yes / No

Solid product

by Legacy Reviewer, Verified Owner Written on May 11, 2012
I bought these so I could use a scope on my .22 CMMG upper. They give me just enough clearance to keep my MBUS sights on the gun and use a quick disconnect mount on the scope for versatility.
Pros: compact, yet well built
Cons: none...
Would recommend: Yes
0 of 0 found the following review helpful.
Was it helpful to you? Yes / No

Too loose, nice try

by Legacy Reviewer, from United States, GA Written on February 16, 2012
Too large, very loose, returned...
Would recommend: Yes
1 of 1 found the following review helpful.
Was it helpful to you? Yes / No

1/2 picatinny riser

by Legacy Reviewer, Verified Owner from United States, WV Written on December 28, 2011
I had a 1/2" riser on my AR and wanted to raise my dot sight a little more to properly view over the front sight. Maybe I should have purchased a 1" riser, but then I would've had a 1/2" being unused. stacking the 1/2" serves my purpose just fine so far, just doesn't look as nice. It's a good product, was just trying to utilize what I had.
Pros: properly raises your sight
Cons: don't stack evenly...
Would recommend: Yes
0 of 0 found the following review helpful.
Was it helpful to you? Yes / No

Burris AR Tactical Mounts 1/2 inch Picatinny Riser

by Legacy Reviewer, Verified Owner Written on July 26, 2011
A little too tight to fit the Picatinny rail on my SIG556, but was able to install it using a flat blade screw driver inserting it in the middle to help spread it wider.
Pros: Nice design
Cons: Fit is too tight!...
Would recommend: Yes
0 of 0 found the following review helpful.
Was it helpful to you? Yes / No
Page
Back
Next

Comments on 16 User Reviews of Burris AR Tactical Mount 1/2 inch Picatinny Riser