Products
2,501 Brands 483 Categories All Departments
Leapers UTG Low Profile Dovetail to Picatinny Rail Mount Adapter
$8.99 $12.97 Save 31%
Browse by Rating
(5 reviews)
Share your Thoughts! Write a Review
Most Helpful Positive Review take ur time
The rails on my rifle are 13.5mm. mounts for this are expensive and the on...
Read More...
Most Helpful Negative Review Good concept, poor execution
This adapter seemed to be the perfect solution to allow scope rings with pi...
Read More...
Sort by
Page
Back
Next

Leapers UTG low Profile Dovetail to Picatinny Rail Mount Adapter

by James, from United States, CA Written on October 11, 2014
Excellent product! This is exactly what you need to get your optic as close as possible to your bore if running out of elevation MOA's, or to aid in attaining proper cheek weld. Quality built, well designed low profile adapter....
Pros:
  • Great product, does what its intended to do.
Cons:
  • None
Best Used for:
  • Its purpose
Would recommend: Yes
0 of 0 found the following review helpful.
Was it helpful to you? Yes / No

nice conversion to picatinny rail mount from dove tail

by Legacy Reviewer, from United States, MO Written on February 4, 2013
these work great put them on my silent cat 22 pellet gun gives all kinds of options for mounts
Pros: very low profile easy to install work well...
Would recommend: Yes
0 of 0 found the following review helpful.
Was it helpful to you? Yes / No

Decent idea, pays to have a few around

by Legacy Reviewer, Verified Owner from United States, FL Written on January 28, 2013
Haven't needed to use these to adapt weaver Scope Mounts yet, but have bought and used plenty for weaver "accessory mounts". All of the weaver mounts I have adapted so far are single slot, and these adapters do not detract from the appearance and functionality. Hard to get them to expand/retract at first, but I dab a little silcone lube on the silver aluminum "slide" rods, then all is good. Pays to have a couple of these around, just in case.
Pros: Minimal/compact footprint. Barely know they are there.
Cons: Retraction and expansion difficult at first...
Would recommend: Yes
0 of 1 found the following review helpful.
Was it helpful to you? Yes / No

take ur time

by Legacy Reviewer, Verified Owner from United States, IN Written on January 10, 2013
The rails on my rifle are 13.5mm.
mounts for this are expensive and the ones avail are way high. I like to mount as close to center bore as possible, now I can use picatinny low mount rings.
This adapter stretched to fit and does include small stop pins to fit in receiver holes of an air rifle, however when you tighten the rings to rail, they want to collapse down raising the sides, so you have to adjust their scope stop pin to keep it square/level with your scope ring bracket(pushes up), then tighten securely and they do not budge, the 2 sliding rails of the adapter also tighten/lock with a very small size allen wrench after you have the rings tightened to base. The rings centered exactly and would do so on a 11mm as well by design. Whether they hold up depends I think on the strength of the rings holding/clamping them on.
Pros: centers exactly
Cons: adjustment time, weak link...
Would recommend: Yes
1 of 1 found the following review helpful.
Was it helpful to you? Yes / No

Good concept, poor execution

by Legacy Reviewer, Verified Owner from United States, MD Written on December 15, 2012
This adapter seemed to be the perfect solution to allow scope rings with piccatiny/weaver mounts to fit an airgun with 11mm dovetail. The problem is it does not work well. By nature of the design, the adapter flexes when the scope mounts are tighened. The result is a weak grip on the dovetail, which causes scope to fall off the rifle.
Pros: Easy to install
Cons: Does not provide secure connection...
Would recommend: No
2 of 2 found the following review helpful.
Was it helpful to you? Yes / No
Page
Back
Next

Comments on 5 User Reviews of Leapers UTG Low Profile Dovetail to Picatinny Rail Mount Adapter