Products
2,497 Brands 483 Categories All Departments
Weaver Thumbnut SPR 1in Mount
$61.79
Browse by Rating
(5 reviews)
Share your Thoughts! Write a Review
Most Helpful Positive Review it works
It's a good product. It does it's job lifting the scope high enough to put a backup sight on. However the metal screws are brittle and I've already st...
Read More...
Sort by
Page
Back
Next

Weaver Thumbnut SPR 1in Mount

by Ozarksportsman, from United States, MO Written on September 21, 2014
I ordered this to put on top of my Colt AR6720 LE carbine. Since it has the A2 front sight needed the height. I barely clear the front sight. It does however meet another need of mine and that was to still have my magpul rear sight still on the top rail. It replaces the riser block which I originally had on it but made the rifle look so blocky.
The fit and finish was outstanding and have always been a fan of 4 screws per ring. The reason it didn't get 5 stars is the distance from font of the front ring to the rear of the back ring is too wide for my tactical scope tube. I've topped my AR with a Truglo TRU-BRIGHT Xtreme compact 4x32 tactical with mil dot reticle, and had to spend about an hour filing and chamfering the leading edge of the ring part to match the angle on the scope tube to the reticle. Otherwise I had to have the scope out of focus to mount it up....
Pros:
  • Fit and finish
  • Looks great,
  • quick mount thumb screws
  • height
Cons:
  • too much distance between rings
Best Used for:
  • full size scopes
Would recommend: Yes
1 of 1 found the following review helpful.
Was it helpful to you? Yes / No

Great Mount for AR15

by J-Rod, from United States, SC Written on September 9, 2014
I'm very satisfied with this mount. I was looking for a reasonably priced one piece scope mount for my AR15. This mount fit perfect, and gave me the forward eye relief that standard scope rings would not. It gives enough height to mount a 50mm objective lens on a M4 rifle. The mount fits great, and looks good on my rifle. I'll probably buy another one for my other AR15. The thumb screws are a great bonus in case you want to quickly swap to a carry handle or iron sights....
Would recommend: Yes
0 of 0 found the following review helpful.
Was it helpful to you? Yes / No

"GOOD STUFF MAYNARD"

by chopper, from United States, CA Written on August 26, 2014
This sets on top of my DPMS 308 build. I bought a Redfield Battle zone because it sets up for 223 ss well 3x9 x42 with after market Vortex cap covers numbers 5 and 6 (rubber female opening slips on scope just right}.The Weaver thumbnut SPR holds it all just right. My scope takes a lot of real estate on top of my AR
but with the SPR all the way back to charging handle the eye relief is just right for me. Also note that I'm running a UTG rifle butt stock this does affect positioning for me in and where eye relief and SPR placement are concerned....
Would recommend: Yes
0 of 0 found the following review helpful.
Was it helpful to you? Yes / No

No riser required!

by Russ Laya, from United States, TX Written on August 6, 2014
It stays on the scope tight, doesn't get loose, and is the perfect height on top of my AR-15 so I don't need a riser at all. Very well made, can't say enough about this mount except get it. It's all you'll need for your AR....
Would recommend: Yes
1 of 1 found the following review helpful.
Was it helpful to you? Yes / No

it works

by Legacy Reviewer, Verified Owner from United States, NV Written on July 8, 2014
It's a good product. It does it's job lifting the scope high enough to put a backup sight on. However the metal screws are brittle and I've already stripped one of them with a flat head,but it can be hand tightened still so it's not that big of a deal.
Pros: elevates scope
Cons: screws stick out...
Would recommend: Yes
1 of 1 found the following review helpful.
Was it helpful to you? Yes / No
Page
Back
Next

Comments on 5 User Reviews of Weaver Thumbnut SPR 1in Mount