by
JFC,
Verified Owner
from TX, United States
Written on August 12, 2025
Product fits tight on the helmet, holds the ear pro in place, and simply works great once properly adjusted.
Would recommend: Yes
0 of 0 found the following review helpful.
Was it helpful to you?
Yes
|
No
You said this review was not helpful.
Would you like to change your vote?
by
Rob,
from NV, United States
Written on May 16, 2025
Does not create a tight enough seal to protect your hearing especially when wearing eye-pro. I just chose to run my ear-pro under the helmet or use in ear protection when comms are not as much of a priority. This might work for some large headed mutants but it did not work for me.
Would recommend: No
0 of 0 found the following review helpful.
Was it helpful to you?
Yes
|
No
You said this review was not helpful.
Would you like to change your vote?
by
Michael O,
Verified Owner
from GA, United States
Written on February 24, 2024
These worked great with my Team Wendy Exfil Ballistic paired with Peltor Comtac V's
Would recommend: Yes
1 of 1 found the following review helpful.
Was it helpful to you?
Yes
|
No
You said this review was not helpful.
Would you like to change your vote?
by
Timothy Riley,
Verified Owner
from KY, United States
Written on June 28, 2022
Ordered them in for my Opmod pro ears and they work great. the attachment points come off the wire if you twist and pull and you have the ability to attach any hearing protection the has the basic shape and design of the comtacs. The make it easy to put in helmet and secure ear pro to your head and with the bump helmet they apply enough force to keep helmet secure and ears protected, without causing headaches
Would recommend: Yes
0 of 0 found the following review helpful.
Was it helpful to you?
Yes
|
No
You said this review was not helpful.
Would you like to change your vote?
by
Ninja,
from WA, United States
Written on February 28, 2022
Mounted to Team Wendy Exfil LTP w/ upper end "airsoft grade" comms/ear-pro.. Had to swap the "ear cup brackets" since they use smaller studs and then bend the ends since the Peltor's use thinner wire, so I'm hoping some Sora Adapters will help solidify that connection.. I haven't field tested them yet but they were plenty snug upon install and feel very secure, but still easy enough to detach without having to fight with them, *plus* no small hardware to potentially lose (win/win).. Might not be "as solid" as the bolt-on versions but any blow that would be hard enough to knock them off would most likely send you to the ER anyway..
Would recommend: Yes
0 of 0 found the following review helpful.
Was it helpful to you?
Yes
|
No
You said this review was not helpful.
Would you like to change your vote?
by
trblcoming,
Verified Owner
from NC, United States
Written on September 27, 2020
Fits my team Wendy helmet perfectly. Holds my Peltor headset in a comfortable position. It makes the ear protection ride just slightly lower than I would prefer (about 1/8 of an inch). I could alleviate that with some additional padding in the helmet. I would purchase this again.
Would recommend: Yes
0 of 0 found the following review helpful.
Was it helpful to you?
Yes
|
No
You said this review was not helpful.
Would you like to change your vote?
by
smoke,
from GA, United States
Written on January 24, 2019
The Peltor Adapters Fit great , The lock up to the helmet is out standing, When pressed inward to your headd it has one of the best fits we have ever used, Great product , Great company to work with Quick service, Thanks Smoke
Would recommend: Yes
1 of 1 found the following review helpful.
Was it helpful to you?
Yes
|
No
You said this review was not helpful.
Would you like to change your vote?