by
JL67,
Verified Owner
from NY, United States
Written on November 8, 2025
The Bushing Compensator did need to be fitted, I figured as much from all the research that I did. I put it on a Dan Wesson Pointman Major .45 about 1 hour to fit it. Looks great on the gun. I went with the stainless steel. My D.Wesson is blued with SS acsents . I would have given a higher rating but the compensator had black marks on both flat sides. I had to polish it , took 20 more minutes but the marks did come out.I expected a little better Quality control from Wilson Combat. No fault of Optic Planet. Have not tried it out yet but will soon.
Pros:
- Looks great
- easy to install, exactly as advertised
Cons:
- Minor Blems
- Finish could be better
Would recommend: Yes
0 of 0 found the following review helpful.
Was it helpful to you?
Yes
|
No
You said this review was not helpful.
Would you like to change your vote?
by
Hosh,
Verified Owner
from CA, United States
Written on October 26, 2025
This item, I am sure, is great for most 1911s. However, this will not fit a SIG 1911 XR Full. The bushing is too thick to fit between the barrel and the slide.
Would recommend: No
0 of 0 found the following review helpful.
Was it helpful to you?
Yes
|
No
You said this review was not helpful.
Would you like to change your vote?
by
Bushing,
Verified Owner
from MN, United States
Written on October 21, 2025
The bushing of this brake is too thick to fit between the slide and the barrel of a SIG 1911 XR. This is the only reason I returned this item. It is very disappointing I didn't even get to try it.
Would recommend: No
0 of 0 found the following review helpful.
Was it helpful to you?
Yes
|
No
You said this review was not helpful.
Would you like to change your vote?
by
ERIC WILLIAMS,
Verified Owner
from CA, United States
Written on February 11, 2025
took a few hours of sanding and buffing but fit is good once done.
Would recommend: Yes
0 of 0 found the following review helpful.
Was it helpful to you?
Yes
|
No
You said this review was not helpful.
Would you like to change your vote?
by
Dan,
Verified Owner
from TX, United States
Written on January 4, 2025
I have 5 1911 government pistols. This bushing comp is so oversized, there is no chance of it fitting with " minor" fitment. I would have to have it machined, then refinished costing me triple or more the cost I anticipated. The diameter is so large, I would assume that it snuck by quality control (if wilson has such a thing) and made it to my mailbox for $80. Second time I've been less than impressed by Wilson. Never again.
Would recommend: No
0 of 0 found the following review helpful.
Was it helpful to you?
Yes
|
No
You said this review was not helpful.
Would you like to change your vote?
by
Dan,
Verified Owner
from TX, United States
Written on December 31, 2024
Doesn't fit any of the 4 government 1911s I own. It's diameter is far too big for "minor fitting." It would need to be remachined and refinished making it a giant waste if money. 2nd time I've gotten garbage wilson combat products. Never again.
Would recommend: No
0 of 0 found the following review helpful.
Was it helpful to you?
Yes
|
No
You said this review was not helpful.
Would you like to change your vote?
by
Cheese,
from TX, United States
Written on May 17, 2024
Does not fit not even close alot of sanding gunsmith
Would recommend: No
0 of 0 found the following review helpful.
Was it helpful to you?
Yes
|
No
You said this review was not helpful.
Would you like to change your vote?
by
Hotrox54,
from OR, United States
Written on September 26, 2023
It was a very snug fit as you would expect. I haven’t had a chance to take it to the range yet to see if it indeed reduces muzzle flip. Even a little would be nice. It appears to be a well machined product and from the research I did of other cheaper brands,the placement of the porting of the Wilson Combat model would be the most effective and the primary reason I chose it.
Pros:
- Fit and finish. Ease of installation.
Would recommend: Yes
0 of 0 found the following review helpful.
Was it helpful to you?
Yes
|
No
You said this review was not helpful.
Would you like to change your vote?
by
Frankie4fingers,
Verified Owner
from CO, United States
Written on April 11, 2022
While I realize that the tolerance across all makes of 1911 are different the install might require modification of the slide or the compensator or both. I wasn't willing to do that for simple cosmetics. I was way disappointed. This isn't truly a "drop in" product.
Cons:
- The box is where it looked cool from.
Would recommend: No
0 of 0 found the following review helpful.
Was it helpful to you?
Yes
|
No
You said this review was not helpful.
Would you like to change your vote?
by
nl,
from OK, United States
Written on March 8, 2021
Put this on a Kimber. A bit tight but not too tight. Put it on your slide a twist it to check for fit before assembling the first time, but outside of that, it does it’s job. There is a video on Wilson’s website showing it being put together and they do it wit the spring in place before putting the slide back on the frame and that is a good choice.
Would recommend: Yes
4 of 4 found the following review helpful.
Was it helpful to you?
Yes
|
No
You said this review was not helpful.
Would you like to change your vote?