Your Browser is Outdated
Compare (0)
1 item has been added
Add at least two items to compare
Longer screws needed for Kimber CDP II
Mount is of high quality and mated perfectly with my ADE green dot. I encountered an issue with the supplied screws being too short to fit my Kimber CDP due to the cut out design of Kimber's rear sight. I ordered 4-48 x 3/8 flat head screws on-line for 31 cents each and they worked perfect. I don't expect the mount supplier to provide screws for all the various mounts but it would have been nice.
Would recommend: Yes
Good sight, it didnt fix my kimber exactly right ...
Good sight, it didnt fix my kimber exactly right but I made it work with another sight adapter. The only thing, I wish these sellers selling these adapter would take a few pictures of them. Show the side, type of sight cut, bomar, novak, mil stardard, maybe put a measuring device near by too wouldnt hurt. Show the top, bottom sides, everything it is hard to guess what you are getting when you only see the top side of something that attaches from the bottom.
Would recommend: Yes
Good match to Umarex Colt 1911 CO2 pellet gun
I wanted to put a red dot on my Umarex Colt 1911 CO2 pellet gun to better match my 1911 comp gun. This plate fits correctly, and matched to an ADE RD3-009 red dot, has made a dandy 10 meter training gun. Although I used blue Loctite on the screws, recoil is a non-issue with this setup, at the Umarex 1911 does not have a reciprocating slide.
Would recommend: Yes
Good Mount! ?
Solid mount and fits a wide variety of mini red dot sights. Does not fit the bottom of older Optima 2000 pattern sights. dovetail was tight but was not hard to install on Springfield slide. I mounted this on a 9mm 1911 and have run probably 400 rounds through the gun with no problems. Mount is still firmly installed and sight has held Zero well.
I must revise rating. This base was mounted on a custom STI based gun with a Springfield slide and a compensated barrel chambered in 40 S&W and carrying a Redfield Accelerator sight weighing 1 oz. I didn't use the gun much over the summer. I recently took to a pin shoot. On the sixth round fired the screws stripped out of the base plate and the sight went flying back past my ear. I will be contacting the supplier for service.
I must revise rating. This base was mounted on a custom STI based gun with a Springfield slide and a compensated barrel chambered in 40 S&W and carrying a Redfield Accelerator sight weighing 1 oz. I didn't use the gun much over the summer. I recently took to a pin shoot. On the sixth round fired the screws stripped out of the base plate and the sight went flying back past my ear. I will be contacting the supplier for service.
Would recommend: Yes
Great and stable fit
I have installed this on 1911 and a PPQ. WIth the PPQ, of course, you'll need to build your own dovetail.
Fits fine with the Burris Fastfire. Do note that they use different screws than the ones that comes with the Burris Fastfire!
The latest version of the mounting plate comes with two sets of screws for different red dot sights. I've been shooting with it for more than a year now and still very happy with it.
Fits fine with the Burris Fastfire. Do note that they use different screws than the ones that comes with the Burris Fastfire!
The latest version of the mounting plate comes with two sets of screws for different red dot sights. I've been shooting with it for more than a year now and still very happy with it.
Would recommend: Yes
Fits well after shaving off 1 MM. Sight flew off.
So for a review you are suppose to get binoculars 10x. I recieved a magnifying glass, like I'm 80 years old.
Fits well after I shaved about 1 MM off of the side. I have a LLAMA which is a Colt 1911 replica. The screws fit just fine. And it came with a set of longer screws I guess after all the reviews. I had a mini green dot laying around and figured I'd put it on something. I ran across this mount by mistake but I am glad I did. I use this for my hunting sidearm.
Update. Turn a oit the screws were too small. 6 shots and the sight hit me right in the mouth. So going go Lowes to get replacement screws. Should work. Need to be 3/16 longer.
UPDATE: M3 .50 6MM screes that I got on Amazon for less then $2 fit perfectly. Old ones are 3MM so it should hold now.
Fits well after I shaved about 1 MM off of the side. I have a LLAMA which is a Colt 1911 replica. The screws fit just fine. And it came with a set of longer screws I guess after all the reviews. I had a mini green dot laying around and figured I'd put it on something. I ran across this mount by mistake but I am glad I did. I use this for my hunting sidearm.
Update. Turn a oit the screws were too small. 6 shots and the sight hit me right in the mouth. So going go Lowes to get replacement screws. Should work. Need to be 3/16 longer.
UPDATE: M3 .50 6MM screes that I got on Amazon for less then $2 fit perfectly. Old ones are 3MM so it should hold now.
Would recommend: Yes
Works good for my sd40
Fits my S&W SD40 great. Need the right type of scope for it to fit.
Would recommend: Yes
Great addition to any M&P 2.0.
With how limited the M&P 2.0 is it's great to have a way to throw an optic on it. Install was pretty easy. Highly recommend.
Would recommend: Yes
Fits perfectly, and very sturdy
This one fits either my S&W SD9VE or MP Shield, so I can install ADE or Vortex Venom red dot. 100% satisfaction.
Would recommend: Yes
PULL THE TRIGGER YOU WONT REGRET IT
I WAS KINDA IN THE AIR ABOUT THIS PURCHASE AFTER READING THE REVIEWS BUT AFTER GETTING IT MOUNTED AND SIGHTED IN 150 ROUNDS LATER ITS STILL HOLDING ZERO AND OPTIC IS STILL TIGHT
Would recommend: Yes
There are no reviews that match your criteria. Would you like to review this product?