Your Browser is Outdated
Bravo Company Mfg Gunfighter Trigger Guard
As Low As
$7.99
Save Up to 40%
Compare (0)
1 item has been added
Add at least two items to compare
Most Helpful Positive Review
Great addition
This trigger guard works great on my AR. Not only does it provide more room for firing with a gloved finger, the FDE matches my Magpul grip perfectly. Easily installed. Looks like it was part of the original lower. Great buy. Next build, I will definitely buy another.
Works great with gloves
I swapped out my geiselle basic trigger guard for this. Its a slightly larger area for a layer of gloves. The plastic feels much better against your middle finger with a high grip.
Pros:
- Plastic
- Larger space
Cons:
- plastic
Would recommend: Yes
Good looking and functional trigger guard
I've been using BCM and Magpul trigger guards for over a decade on my rifles. The BCM looks good, provides lots of room for a gloved finger, and feels good. If you have a mil-spec AR lower, this is a great replacement for the GI trigger guard.
Would recommend: Yes
Good trigger guard
Basic trigger guard install, no rattle, and smooth edges so there is no discomfort on the knuckle that it rests on. Does the job.
Would recommend: Yes
BCM Trigger Guard
Fit well and was shipped to my door in an acceptable amount of time. Fit perfectly on my aero lower.
Would recommend: Yes
Great value
Economical and IMHO not inferior to metal.
I have another polymer version from Magpul, and also an aluminum version. They are all equally functional, this one being far cheaper.
Gloves or not, I think one of these are a must - they eliminate the standard trigger guard rubbing your middle finger to a blister.
Be careful when drifting out the roll pin to remove the stock guard, and when installing the new one. I have a drifting tool, but it can be done with a regular punch, just be sure to support properly to avoid breaking the lower. Watch a video or two.
Minor gripe: could've included an allen wrench. No biggie for me, but would be frustrating to someone who doesn't have one.
I have another polymer version from Magpul, and also an aluminum version. They are all equally functional, this one being far cheaper.
Gloves or not, I think one of these are a must - they eliminate the standard trigger guard rubbing your middle finger to a blister.
Be careful when drifting out the roll pin to remove the stock guard, and when installing the new one. I have a drifting tool, but it can be done with a regular punch, just be sure to support properly to avoid breaking the lower. Watch a video or two.
Minor gripe: could've included an allen wrench. No biggie for me, but would be frustrating to someone who doesn't have one.
Pros:
- value
Cons:
- allen wrench not provided
Would recommend: Yes
All around upgrade
This is a nice upgrade over the standard flat trigger guard. It adds a decent amount of space near the trigger to allow for shooting gloves. Plus it comes in numerous colors to add a splash of color to match up with your stock.
Pros:
- Easy to install
- solid construction
- BCM Quality
Cons:
- foliage green color is a little lighter than anticipated
Would recommend: Yes
great fit and function!
Anything that i have pirchased from BCM has been spot on. The selection, cost and above all fit would compete with any manufacturers out there. Would definitely purchase again!
Would recommend: Yes
1 of 1 found the following review helpful.
Nice fit and easy install
Trigger was easy to install and matched my grip and Bcm stock perfectly
Would recommend: Yes
Bcm trigger guard
Can't go wrong. It's BCM!! Trigger guard is nice, large enough for gloved trigger finger. Installs easily. It's great.
Would recommend: Yes
Love bcm products
Was an easy decision to pick this up. Never been disappointed with a bcm grip, fore grip and now trigger guard. Came with all the correct hardware. Even has dimples to help keep it in place while installing. Definitely recommend.
Would recommend: Yes
There are no reviews that match your criteria. Would you like to review this product?