Your Browser is OutdatedBOOS DAD from United States, VA Public Profile
Reviews by BOOS DAD
Life Saver
Written on Feb 03, 2024
Quite a while back I bought a BCG for a future build, when I got it I gave it a prefuctery look and stowed it in an amp can with other parts.I should have examined it more thoroughly,
as I recently found out, this BCG was missing the ejector pin (Doh!). The BCG,other than the missing pin was na otherwise nice unit. Believe me, I looked this over very thoroughly, It's a very well mede unit. The price was very reasonable. It was more than worth the cost!
as I recently found out, this BCG was missing the ejector pin (Doh!). The BCG,other than the missing pin was na otherwise nice unit. Believe me, I looked this over very thoroughly, It's a very well mede unit. The price was very reasonable. It was more than worth the cost!
1 of 1 found the following review helpful.
ADAPTABLILITY
Written on Jan 30, 2024
I tried every combination of front and back straps. The beavertail allows for a higher grip, as it matches the contour of the lower as close as is possible.Found the combination that fit my hand perfectly. Also the texturing is really good. The battery storage is a definite necessity, for me.
Trigger pull complaints
Written on Dec 15, 2018
Review for
RISE Armament RA-140 Super Sporting Trigger
I own several (5) of these triggers. Every one consistently reads 4 lbs. on my gauge (close enough for Govt. work). Since the trigger is so consistent, I barely notice the 1/2 lb. difference.
The problem that some people are experiencing with heavier trigger pull MAY be due to excess tightening of the set screws at the bottom of the trigger housing. If these set screws are too tight, the trigger pull will increase. Check the instructions provided by the manufacturer.
The problem that some people are experiencing with heavier trigger pull MAY be due to excess tightening of the set screws at the bottom of the trigger housing. If these set screws are too tight, the trigger pull will increase. Check the instructions provided by the manufacturer.
96 of 99 found the following review helpful.
Form, Fit and function
Written on Oct 08, 2018
I bought this cover for my Trijicon RX30 Reflex Sight. It fits snugly, but not too snug, It's easy to slip on, I put the front on first, then use two fingers to slip it over the back. It covers the whole sight and there is no way this thing will come off accidentally. I tried it on an older RX-06 sight with an American Defense QD mount and it works on that too, it's actually a bit tighter.
Great fit and finish
Written on Sep 22, 2018
I don't think you'll find a better QD end plate for this price. The finish looks great it is a satin finish, not flat, but not shiny. My next AR lower I build will definitely have one of these end plates on it. All the QD sling swivels fit very well. I use the Bravo Company D-Ring swivels. With these QD end plates you get good quality for a really good price.
Beats the original equipment dust cover by a mile
Written on Sep 22, 2018
Every one I've installed (7 total) fit perfectly. Unlike the original dust covers, you don't have to tear you AR apart to remove/replace these covers. I haven't had them for too long so I don't know how they will stand up, but they seem pretty solid/tugged to me.
Rugged, light weight, super value for the money
Written on Sep 11, 2018
I now have three of these, two 0.83" (absolute co-witness), and one 1.00" (1/3 co-witness). The 1.00" riser weighs 1 oz., while the 0.83" is about 7/8 oz. All three are paired with an AT3 RD-50, 2 MOA red for sight. sight and riser weight approx. 4.5 oz.
1 of 1 found the following review helpful.
Versatile, utilitarian, looks good and works well
Written on Sep 05, 2018
I needed battery storage capacity. Like the idea of being able to try different inserts. Finger groove option was great, but I don't like them, so I went with the straight front strap. The medium back strap suited my hand best. i have smallish hands but longer fingers. All the inserts fit very snugly, so they're not likely to ever move unexpectedly. Initially, i had the EPG16 grips on the rifle, I prefer the more vertical angle of the EPG16, but they don't have a storage compartment. I have a UTG hand guard in FDE on this rifle, and the SDE is a real good match. I found the MAGPUL FDE to be too light, not a good match at all.
There are no reviews that match your criteria. Would you like to
reset filters?