Bryan Verduzco from United States, CA Public Profile

I bought this to use for hunting in California and it's Performance has been pretty great. Used it to take a shot at 250 yards and got decent expansion on a mule deer which was more than I was expecting. Would recommend for taking shots within 300 yards!

I got this scope, mounted it and zeroed it at the range. I have to say that for the money this is a fantastic scope! I didn’t buy it expecting it to be as good as say a vortex razor hd, but it has very good features. The eye box at 1x is pretty forgiving so you can get a quick shot off if need be, the eye relief is also pretty forgiving at 1x. At higher magnifications the eye box does get pretty tight, but that’s expected when you have such high magnification. Overall it’s a fantastic scope and I highly recommend it!

Let me start off by saying that if you have an older non-ranch mini 14, this is basically the only option you have to mount any sort of optics on it. With that said, this mount is pretty good if you’re patient and know what you’re doing. Getting the two elevation screws perfectly lined up and getting the adjustment knob to tighten down without the mount popping out of place is difficult but once you find the sweet spot, this mount is rock solid. Took it out and zeroed it and then took it on a hunt and it stayed zeroed so I definitely give it a thumbs up!

this is my second stag left handed upper that I have purchased. Both have been well made and high quality, this one is no exception. I was able to put my rifle together with no issues and this thing is holding up just fine.

I bought this for a new build I was putting together. Stag has been my go to for bolts since all of my ARs are left hand, so of course they were my first choice. My previous two Stag left hand bolts were well made, I have one from 2011 that is also phosphate coated with chromelined inside and it has never failed me in the 9 years I've had it, I have never had a malfunction in that AR. my last Stag bolt was an ar10 nitride one and it too has been stellar and well made, no issues. This one that I just purchased, however, is not as good as the others. The phosphate coating on the one I bought was really rough, made cycling the bolt when I first got it a little tough. The other issue I had is the edges along the belly of the bcg (the bottom of the carrier) were extremely sharp compared to my other two bolts, it cut my finger when I first installed it and did a little damage to the inside of my receiver. Luckily noting else was out of spec, and a little bit of use and some deburring to the bottom edges made this bolt as good as the others, but I was a bit disappointed with the initial quality of the bolt which is why I gave it 3 stars.

I bought this to complete an ultra light build (and because I live in california, featureless builds need to have a brake and not a flash hider). this is just about the smallest brake ive seen and once mounted adds about half the length that an a2 flashhider adds. I haven't tested the effectiveness of this brake, but 5.56 already has very mild recoil so Im sure it will help a bit. Also the crush washer included is decent, should work perfectly fine to install this brake.

Let me start off by saying that I really love this handguard, I dont think it weights more than 10oz with the barrel nut and screws (I bought the 15 inch version). It is the clamp on style of handguard and uses a torx head for the handguard screws, which I found mildly annoying since I didnt have the right one and had to go out and buy it, but they dont strip easily so thats good. the barrel nut itself uses a 1 1/4 inch crows foot and is made of steel, no trouble torqueing it on my upper. Only thing I don't like is that the finish doesnt match my upper, its a little lighter and not as smooth, but aside from that I like everything about this handguard and will definitely buy another in the future.

I bought this for a few AR's and it fit them all just fine. I will say some AR's had a much harder time installing it since it fit super tight, but a little lubricant, some muscle and a few swear words and they installed just fine. These are the most comfortable grips to use when you cant fit your hand behind a sparrow or juggernaut featureless grip.

I bought the left handed loop only and it worked great with my blackwood trading co pioneer carbine wood stock, it sticks out over the stock and allows me to attach a sling to the back since the stock doesnt have a way to attach a sling. Would definitely recommend this.

Not much else to say about it. It is a good target and stand, its 3/8 inch so you can gather from that what it can withstand. Havent taken it to the range yet but all the components feel like high quality so I am sure it will do fine.