Your Browser is OutdatedReviews by Dan
Addendum to "Throw-N-Go"
Written on Oct 28, 2021
The measurements listed are for the 50 shell bandolier. Measurements for the 56 shell are unknown to me as I do not have it. Airsoft Trishot, 3 round burst shotshell mags fit VERY snuggly. No worries about losing any when running & gunning. 12g CO2 bulbs/cartridges also fit perfectly.
Throw-N-Go!
Written on Oct 14, 2021
Laid flat- its approx 31"L (a bit of a let down because I was expecting it to be 26.5" as stated in listing...being on the smaller side of human beings, I don't need things to be large/loose) with a width of 2 15/16" (call it 3") and a very soft/pliable denier. The elastic shell band is in the middle of the strap with two rows of stitching between each shell.
Using for Airsoft Vz-61 Mid-Cap Mags
Written on Oct 14, 2021
Easily fits three, 38bb Mid-Cap mags which are curved and have the following dimensions: 5"L x 1 3/8"W x .75"H. Closure flaps are adjustable, removable and/or can be folded into pouch (behind mag) for quicker deployment. All the stitching is very crisp, clean and uniform, same goes for overall construction of the pouches. Elastic band enhances retention of each pouch. As shown in product listing images. 10/10 would buy again.
Cheap, functional
Written on Jun 29, 2021
Review for
AIM Sports Inc AR Mil-Spec Buffer Tube
Outer diameter, measured horizontally across the rear of tube = 1.15in. Sharp, clean threads. Only a couple small issues with it: the finish is on the glossier side of a semi-gloss black, and there no numbers or markings of ANY kind on the top of the tube to indicate stock position..(my GBBR AIRSOFT buffer tube even has that.........)
Loosey goosey!
Written on Jun 29, 2021
Review for
Aero Precision M4 Sliding Stock
Gotta say I'm pretty under-whelmed with this product. The fitment of this to an AIM Sports mil-spec buffer-tube was shockingly bad. According to Mil-Specs listed on wingtactical dot com, the AIM sports tube is within spec at 1.15in dia. The inner dia of this stock is 1.178in! It would've actually fit the commercial-spec Luth-AR tube if it weren't for the beautifully machined fillet of its ventral adjustment rib! My AIRSOFT G&P M4 GBBR Stock actually fits the mil-spec tube better than this.
1 of 2 found the following review helpful.
Steel, fits commercial-spec
Written on Jun 22, 2021
Review for
Luth-AR Carbine Lock Ring/Castle Nut
Threads easily onto the LUTH-AR Commercial-Spec buffer-tube/receiver extension (wasn't sure it would because nothing is listed anywhere saying that fits one spec or the other specifically) that I also purchased. Sharp, clean threads and steel what more could you ask for?
Fits the APS CAM870 Drop Tube Adapter (AIRSOFT)
Written on Jun 22, 2021
Review for
Luth-AR 223/308 6 Position Buffer Tube
Threads perfectly into the buffer-tube adapter (DTA: Drop Tube Adapter) for the APS CAM870 Series shell-ejecting AIRSOFT shotguns. Don't forget to grab the LUTH-AR castle-nut to cinch it down. Tube is not steel. *Shaka*
Fixed Airsoft GBBR Charging Handle
Written on Jun 20, 2020
I have an airsoft G&P M4 WOC GBBR (gas blowback rifle) challenge kit that I completed. The charging handle latch broke (due to it being aluminum), it actually tore out at the pivot pin hole (after several hundred bbs). I rolled the dice and picked this up, whaddaya know-it fit perfectly! Zero modification, just tapped out the old pivot pin and installed this steel latch with the included roll-pin. Easy breezy.
There are no reviews that match your criteria. Would you like to
reset filters?