Your Browser is OutdatedReviews by GunKnightSwift
Built like a tank but not very Brakey
Written on Nov 23, 2020
I have this affixed to my tromix 16" 458 socom barrel. It goes on fine except that there are no surfaces to get a wrench on it. I ended up shoving some punches through the holes in order to get it to mount properly. After shooting some rounds with and without the brake it doesn't seem to make a huge amount of difference in felt recoil. A good thread protector but not much else. but for 43 bucks what do you really expect.
2 of 2 found the following review helpful.
Have issues with gas block alignment? Look no further
Written on Nov 11, 2020
Review for
SLR Dimpling Jig Gas Block
Before I got this jig I had a few different methods of confirming gas block and port alignment. The spaghetti method, pencil method, a few specific products on the market that were made specifically to help with alignment. all of which had varying degrees of success. But let me tell you this, DIMPLE YOUR BARRELS WITH THIS THING! It takes all the guess work our of where exactly your port is. It is way easier to get perfect gas alignment when the barrel is cut specifically for it. If you have problems with gas block alignment get this thing.
2 of 2 found the following review helpful.
Does everything you want but nothing you don't
Written on Oct 26, 2020
Review for
CMMG, Inc Mil-Spec Trigger Assembly Kit
These are a no frills low cost option for people who want the bare bones experience with their Ar's. Perfect for builders experienced and new alike. I kind of use these as placeholders until I have the money for a nicer trigger. Don't get me wrong there is nothing wrong with these triggers and they actually have a nicer set of tolerances than some of the other low cost options out there. If you are going for quantity over quality these are the best bang for buck. If you want a NICE trigger. Go look at any trigger over 120$. Rise, Timney, CMC, etc.
Won't scratch up your receiver
Written on Oct 06, 2020
I had an upper receiver that had some issues with the charging handle staying in place. the big issue was the charging handle had wore away the place where the latch engaged the receiver. This charging handle made the upper viable again as it indexes off of where you place the latch in. Definitely a good option regardless if you have the same issue or not.
I come back for these time and again.
Written on Oct 01, 2020
Review for
UTG Pro AR15 Quick Detach Receiver End Plate
I love these end plates. They offer a great lockup and another option for mounting a sling swivel. I have gone back and added these onto completed guns not only because they are functional but look good as well.
2 of 2 found the following review helpful.
Loads of Fun
Written on Jul 16, 2020
Review for
CMMG, Inc 22LR AR Conversion Kit, Echo
Do you want all of the fun of the AR platform while keeping trigger pulls under 6 cents a pop? Do you want to suppress your AR and actually have it sound quiet? If yes, then get this conversion kit. I have used mine in conjunction with a Franklin armory binary trigger and it is some of the most fun you can have without a sandwich in your hands.
5 of 5 found the following review helpful.
Works well
Written on Jun 26, 2020
Review for
Strike Industries M-LOK Rail Covers, V2
These work pretty well on my Midwest M-lok rail. The only reason why It isn't 5 stars is because there is a tiny amount of play forward and backwards in the slots. Otherwise the covers have done what they need to do.
Worked Perfectly
Written on Jun 26, 2020
Review for
Tacfire Accu Wedge
These worked perfectly to remove the slop between my upper an lower. Keep in mind that they need to be filed down (I used a dremel) to fit your receivers. They are made with extra material on the bottom to be removed so they will fit any receiver.
2 of 3 found the following review helpful.
There are no reviews that match your criteria. Would you like to
reset filters?