Jim K. from United States, PA Public Profile

OK so lets get right to the point, this will not fit without minor modifiaction.

I tried this on an anderson, PSA, BCA, Aero, CA and BKF lowers.

I ordered the first one... it would not even mate up with the rear lug. yeas you could sand it down to fit, but we really shouldnt have to... te one that I did get it to go in with some force, the arch on the rear did not meet up with the receiver... like a 1/8" gap...

I returned it but asked for a replacement, figured I got a dud.

Next one, it fit better in all but was still tight, the rear arch was a better match to the receiver, but still not perfect.

I believe it is all about the rear lug - sand the sides and the bottom so it sits in arther and it should be fine, but then you may run into issues with the pins not fitting... all in all a bad experience. Returned the 2nd and went another route for my upper.

YMMV, but that was my experience.

Try try again AGM.

The laserspeed version is hands down just better... and not by a little but a lot. Why buy this from Laserspeed then ruin in...

I get the FDA laser limitations for non-LE personnel and the lasers themselves are... adequate... but is the illuminator even regulated, it is ust the laser I thought.

The illumination is just HORRID. I know Holosun is notorious for bad illumination on their units but they look like a full power unit compared to this... It so so underpowered it should not even have it...

Now I have tessted it on a PCC, forget it on a rifle, but for PCC distances 25-50 yards I guess maybe sorta kinda the illuminator works??? I still put a seperate IR unit on the PCC (850nm Pard) and the laser can still be seen at 75 yards and not washed out, so functional now.

For the price I guess it is OK, cheaper than the big brands and cheaper than the laser speed offerings unless ou hit a sale. I just have a big problem with putting a seperate illuminator on my PCC with a 4 in 1 unit...

Hopefully they decide to upgrade that slightly in the future. Amazon IR lights smoke this thing... that alone should tell you its quality.

Great foregrip at a decent price, very sturdy polymer and the M-LOK attaches firm. I also got the Amend stock for a matching set.

So far so good, no complaints.

This part kit worked wonders in my G21 build. Everything fit like it should and slide even had the Glock "rattle".

I would not hesitate to buy again.

These are very good for the money. OK maybe Binary... you have to kinda know what you are doing with these. But is Binary all that bad? Just assume going in you will get two shots per trigger movement, if you get one, fine. That removes the safety concerns if you plan for the worst.

Either way, nice crisp break and just an over very fun trigger to shoot.

This thread adapter is no exception. Works great and finish is top notch. Threaded on great. the Mach system in general is great, especially now with the Flash Hider end plate you can buy now.

KVP makes a great product at a reasonable price, can't go wrong with them.

I know LW gets a bad rap from time to time but I have never (knock on wood) had an issue with any of their items. This barrel is no exception. Dropped right in my 45ACP assembled Glock slide (with LW internals btw) and worked like a charm.

I have put about 75 rounds down range with it and not a single hint of the "Glock mark" on the slide, so the finish is durable and looks stylish to boot.

These just flat out work. Nothing Fancy but man does it cut down Flash. A2 birdcage is really good, on a 16", this is good on a 16" or Pistol Length Barrel and has a lower signature.

3 and 4 prong work very well too but gotta watch the branding as some are basically tuning forks... so they may not see the Flash but they will hear the ring lol.

This is a great all around performer and worth the price.

ATN has been making NV for awhile. Their name is a known name in the community and they make budget friendly options. I purchased a match set of these (sequential serial numbers) to make a set of NV binocular. Let me say, they worked great. The bridge is a bit pricey for 3rd party vendors, but still a very low cost NV binocular set.

Gen 2+ is still a very good NV option for the money. For the money I spent you couldn't touch any other set of NV binoculars for twice the cost.

While these are a "hybrid" based on the MUM14, aka not a PVS14, they are still worth it. Hoping parts for these will be easy when needed.

Ms. Milen (My-lin) Yap "My" was my customer service rep that did help me with some minor issues and upgrades. She answered all my questions and was always quick to follow up.

I have no problem endorsing these just for that reason.

ATN has been making NV for awhile. Their name is a known name in the community and they make budget friendly options. I purchased a match set of these (sequential serial numbers) to make a set of NV binocular. Let me say, they worked great. The bridge is a bit pricey for 3rd party vendors, but still a very low cost NV binocular set.

Gen 2+ is still a very good NV option for the money. For the money I spent you couldn't touch any other set of NV binoculars for twice the cost.

While these are a "hybrid" based on the MUM14, aka not a PVS14, they are still worth it. Hoping parts for these will be easy when needed.

I have no problem endorsing these just for that reason.