Your Browser is Outdated
Compare (0)
1 item has been added
Add at least two items to compare
Most Helpful Negative Review
Does not fit sig p320 with Mag well
The finish is really nice and it fits the magazine really well but I was looking for something that would fit inside the p320 legion mag well and this does not. They sell the legion base plates to convert the non legion mags so they fit but I thought these might. The quality is awesome so if you don’t have a extended mag well you should be happy.
Nice Weighted base plate for Glock
These are nice weighted base plates for my Glock mags. Colors for easy recognition of which mag I am looking for on the wall. would buy again if the need arises.
Pros:
- added weight allow for easy ejection
- color for easy recognition
- works with mag wells
Cons:
- None
Would recommend: Yes
Great Product
Looks good and fits well, very happy. Installation was pretty simple as well.
Would recommend: Yes
Base pad for Glock 19.
Great product. Adding the extended base allows for a better grip under mag well.
Would recommend: Yes
Bad design flaw
Does it extend the grip .2" to accomodate more of your pinky, yes. But I'm returning them because even drawing the gun and dry firing for 5 minutes it is extremely uncomfortable because the sharp back edge corners dig into my hand. Should have taken design hints from NDZ's CZ P10 +0 pinky extension. I'll just stay with a 2 finger grip and hang the pinky off the bottom before I would use these on my mags.
Would recommend: No
Just right
This base pad is just the right size for me to get a full grip without worrying about additional printing.
Another thing I like is that it goes on and comes off the same as the original, notice the hole in the bottom you use to compress the spring with. I have a +3 extension for my RAMI from another manufacturer that doesn't have this access hole. I haven't tried too hard to pull it off yet but I'm assuming I'll need to work an angled pick in there and try to hook the spring plate so I can compress it enough to slide the base pad off.
One slight negative is that it didn't want to properly seat the nub in the spring plate into the hole in the base pad. It took some finagling. The same thing may happen if I try to re-install the original base pad. Not a real negative, just something to watch out for and double check anytime you swap base pads.
Another thing I like is that it goes on and comes off the same as the original, notice the hole in the bottom you use to compress the spring with. I have a +3 extension for my RAMI from another manufacturer that doesn't have this access hole. I haven't tried too hard to pull it off yet but I'm assuming I'll need to work an angled pick in there and try to hook the spring plate so I can compress it enough to slide the base pad off.
One slight negative is that it didn't want to properly seat the nub in the spring plate into the hole in the base pad. It took some finagling. The same thing may happen if I try to re-install the original base pad. Not a real negative, just something to watch out for and double check anytime you swap base pads.
Pros:
- Size
- Installation and removal same as original
Cons:
- Had to twerk it around a little for it to fully catch
Best Used for:
- Best possible concealment with a full grip
Would recommend: Yes
Makes magazine look dope
Love the look & you get a bit of extra space for a full grip for guys/gals with larger hands.
Would recommend: Yes
CZ P10s base pads
Bought a CZ P10S but with stock base pads my pinky didn't quite fit all the time, sometimes it would stay on and some times would roll off the bottom of the base pad. These base pads extended the grip just enough to have full support for my pinky but not extended so far that I lost the advantage of having the smaller grip of the P10S vs a P10C. As an added bonus they added a little weight to the mags and they drop free even better than before.
Best Used for:
- grip / control
Would recommend: Yes
There are no reviews that match your criteria. Would you like to review this product?