Reviews & Ratings for Meprolight Sights for Walther Pistol Models — 14 reviews — Page 1

These sights are excellent! First, the installation: I bought the 18802 front and rear individually for my PPS M2 to get a break on the price. The rear installed easily with the aid of a sight pusher. No need for filing or modification as they fit the dovetail in the slide perfectly. The front sight fit the slot in the slide perfectly as well and the screw was exactly the right size (it is a slotted head screw). Again, no need for modification as it fit right in. Second, the illumination: these sights illuminate nicely in low and no light. There is a slight white ring around them which makes them adequately visible during the day, but they’re not as visible in light as the original white dot sights (these are night sights after all). I was worried that the illumination would vary between the front and rears since I bought them individually but they match perfectly. They are all steel construction with a matte black finish that matches the PPS M2 nicely. Overall an excellent buy for the money!

As the title suggests, this is the easiest upgrade possible, only tool needed is a small screwdriver. Depress the retaining detet and the old sight slides out. Observe the position of the sighting screw, remove from old sight ant insert to the same depth on the new sight. Re-insert the sights on the slide with the detet depressed. This will return the sight to approximately the correct position.

Super easy to install. Super bright at night. It is easy to find the front site in a hurry. I wish it came as a set as described on the website but they made a mistake on the website but it's still a great site and I ended up buying the rear also

Walther meprolight night sights are very close to being the best deal you can possibly get on price but when you add in quality is becomes a much better deal even than that I find that these are the perfect level of brightness to not distract during the day but be very visible in Dusk and we'll light conditions understated enough to not be a problem visible enough to be useful

Very good sight for the money. Easy for the eye to pick up. Unequaled Low Light Performance and the Brightest Night Sights Available Today. As these are used by Military & Law Enforcement and have a fantastic 12 years usable illumination warranty to original purchaser, I don't see how you can go wrong with them.

I purchased this night sight as a replacement for the factory (#4) plastic sight that came on the Walther 9mm P99 (full size). I wanted the POI to be the same (bullet strikes just above the front post at 7-10yards) as the #4 factory sight. The sight was simple to install and works as expected and the point of impact is almost perfect. The trijicon is bright enough to see clearly but not too bright as to be distracting . I am satisfied with these sights and the price is reasonable. The width and height of the sight are almost identical as the #4 factory sight.

I did a lot of research before I decided to buy the Meprolight sights for my Walther PPQ-M2.
I had all the tool ready when the sights arrived, and just followed the direction.
The front sight only took me 2 minutes to install.
The rear took about 10 minutes.

Note: The spring plunger has a notch in it. The adjustment screw must lock into that notch to secure the rear sight !!!

I took it to the range and my POI(Point of Impact) was left of my POA(Point of Aim).
I turn the screw a few turns counter clockwise and the sights were dead on.

Perfect !!!!!!!!!!!!!
These are the best sight that I have ever had.

I bought this sight as a replacement for the factory night sight on my SW 99 40SW.removing the factory sights and installing the Meprolight took less than 5-minutes to install.
great value, I also bought the front sight perfect match. next will be a set for my Khar PM9

I just installed the Meprolight Night Sights for the PPQ. They are built rugged and tough and seem to be a very good choice. My only caveat is that they are not quite as bright as many of the other sights I have used over the years including other Meprolights. I have a brand new set of Trijicon HDs that I just installed on my G19 and they are an order of magnitude brighter than these. Don't get me wrong, these will work and are very functional for the regular user that wants night sights for a bed side gun but if you train hard and need a set of sights that are much more visible, these may not be for you.

Purchased these for a 9mm Walther PPQ M2. No problems with installation, was nice not needing a sight installation tool to install them! Read some comments about the rear sights fitting a little on the loose side on the PPQ M2. There is a slight groove in the rear sight detent plunger that fits into the windage adjustment screw on the rear sight. Unless the groove and the windage adjustment screw are lined up, the rear sights will be a bit sloppy. Can not report on any changes in POA or POI, haven't been to the range yet.