Your Browser is Outdated
Compare (0)
1 item has been added
Add at least two items to compare
Most Helpful Positive Review
Weaver Multi Slot 10/22 Base System 48335
Typical Weaver quality fit and finish. When I ordered the 48630 Four Hole Skeleton Rings, the service tech at Planet Optics suggested this base. The base and rings were a well matched set for my Ruger. You don't get such knowledgable phone assistance anymore...
Pros: Better than the Ruger base
Cons: None
Weaver Mossberg Rail
I purchased this rail to mount a small light/laser combo on my Mossberg Shockwave 590. The rail mounts as it should. The pre-drilled mounting holes line up and quality is good. Can’t beat the price either. Remember to use a very small amount of locktite on the mounting screws to ensure that they do not back out from the shock and vibration of repeated firing.
Would recommend: Yes
0 of 1 found the following review helpful.
Perfect fit.
My Shockwave came with pre-drilled holes for scope mounting. This Weaver base matched up perfectly to my Shockwave. A little alcohol to clean the pre-drilled holes; a little LocTite Blue on the mounting screws. Then torque the screws down and leave it alone until it "sets up". Piece of cake.
Pros:
- Matched perfectly.
Cons:
- None
Would recommend: Yes
0 of 1 found the following review helpful.
Using WR-MT-BFCFDE-48338 1-piece base on Savage 11 Trophy Hunter XP
This 1-piece base (48338) mounted cleanly on my Savage 11 Trophy Hunter XP, and replaces the 2-piece factory-installed mounts. I did this to add additional support across the action and allow more flexibility with positioning the rings/scope. I am also replacing the factory-installed rings with "Weaver Cross Lock Riflescope Rings, 1-in, Medium height, Matte 49303" so the scope sits lower/closer to the rifle barrel. The factory rings placed the objective lens about .360" above the barrel; the Weaver rings will to reduce this space to around .160".
NOTE: The image that appears for this specific base is incorrect. 48338 is a single, flat piece of metal. [The "image" that more accurately represents this the one that corresponds with WR-MT-BFCFDE-48345.]
NOTE: The image that appears for this specific base is incorrect. 48338 is a single, flat piece of metal. [The "image" that more accurately represents this the one that corresponds with WR-MT-BFCFDE-48345.]
Would recommend: Yes
0 of 2 found the following review helpful.
A "Must Have" product
This rail eliminates the struggle of setting your eye relief with scopes with short tubes. I had a customer needing a 30mm tube scope installed and had problems finding scope ring extensions that didn't cost an arm and a leg. I installed one of these and used standard 30mm rings for a no hassle scope installation. The extra notches make it a very versatile base!
Would recommend: Yes
1 of 2 found the following review helpful.
Great value
Solid mount. Cannot beat Optics planet
Pros: strong base easy to install
Cons: could be shorter maybe
Pros: strong base easy to install
Cons: could be shorter maybe
Would recommend: Yes
Lancer4704
Any large caliber firearm will require constant attention to adjustments. Hard to set up since base tends to raise an lower on elevation. Design does not allow repeatable elevation, on a Mini-14, Mini-30; Garand type action.
Pros: Quality workmanship
Cons: poor engineering
Pros: Quality workmanship
Cons: poor engineering
Would recommend: No
0 of 4 found the following review helpful.
Great item
Fit great, good price and quick shipping!
Pros: Fit, price, quality
Cons: None
Pros: Fit, price, quality
Cons: None
Would recommend: Yes
0 of 2 found the following review helpful.
There are no reviews that match your criteria. Would you like to review this product?