Mike from United States, TX Public Profile

I came across an M1 Garand that has a Brownels, top hand guard with 1913 rail. This scopes mounts easily on the rail with perfect eye relief for this Scout type installation. Mounts far enough forward so ejecting cases are not an issue. The site picture is very bright and one can easily shoot with both eyes open. I have basically the same scope mounted on a Ruger Super Red Hawk in 454 Casull and have been shooting it for nearly 3 years with no issues what so ever. I di not intend to shoot this rifle at extreme long range so this scope will do every thing I want under 300 yds.

I installed this trigger assembly in a Glock 19 Gen 3, whose trigger was factory stock. It was spongy and long pull with a lot of over travel. This trigger took care of the majority of those issues. My group size was consistently smaller with this trigger compared to the factory trigger. This trigger comes with a couple of lighter springs set up that go around the firing pin. They tell you, in the literature, this is not recommended for every day carry. I installed the 4 pound spring after shooting the out of package trigger group with the factory spring. I was Concerned about Light primer strikes but I had none. I was shooting reloaded ammo with CCI primers so I thought this was really good. If I had another Glock I would Install one of these in it.

I bought this upper to compliment a Black Rain Milled Lower I have. I tried a different upper on the Black Rain lower and there was a lot of play between the parts. This upper fit the Black Rain lower very Snug. It was so tight that at first I had to tap it with a rubber mallet to get it to release from the lower. After a couple trips to range and a few hundred rounds it open just fine and when lock up with the pins there is no wobble between the upper and Lower. I was amazed at how light this upper appeared. The machining and finish was perfect. I amounted a 20", Whylie Chambered barrel to this upper, with a Free Float Slotted Fore grip. the Accuracy of this Rifle was all I had hope it would be. The Only issue I encountered was Not with the Upper but the Lower, I guess its the thickness but a Magpul Bad lever will not work with the Black Rain Lower. I was not real thrilled with the Bolt carrier I had so I had so I just ordered a Black Rain Bolt carrier group.

This unit comes with two mounting Options. The unit is some what bulky. It Pivots in all directions which is good. Biggest complaint is the legs are difficult to adjust. It takes two hands to extend the legs. Once it is set up it makes a good steady platform for shooting.

I really like this grip. It fits my hand perfectly. It might be too big for someone with small hands. The grip is texture in a pleasant way, not to aggressive but enough so gun does not slip around in hand. It is a completely different feel from the flat plastic grip that is standard in most lower kits.

I ordered these to cover some mags that did not have the covers. They work great. In fact these seem to snap more firm than some of the originals. If you are not aware these will only work on Magpul Magazines. Other makers mags do not have the bumps for attaching these covers.

I bought this scope to go on a Ruger Super Red hawk in 454 Casull. The Scope is bright, easy to see and not real heavy on an otherwise heavy Revolver. I had read all previous Reviews for several Pistol scopes and decided this was the way to go. I am glad I bought this scope. As other reviewers have stated the eye relief at 4 or greater changes but trying to hold that gun steady at 2 powder is not easy at 7 power impossible. If shooting from sticks or a bag its not bad, but that is the nature of Big Bore Guns and nothing to do with the scope. First thing I noticed was how bright the scope is. Wow. The Second Wow came after the third time to the Range and NO change in zero at all. I hate to admit this but first trip to range I was sitting on a folding chair and after one of the Big Bangs form the Casull, the Chair broke, me, gun, and scope were laying on a concrete floor, the scope hit the floor and I though Oh, Boy, there goes that, but except for a small scratch it works fine and never lost Zero. I would not recommend this for a test, but I think the scope is pretty darn tough. So far I have shot over 300 full pressure loads of 45 Colt, and over 100 mid load Casull and its right on the money. I own lots of Scopes, but this is my first Burris. It will not be my last.

I ordered this rail because I have a Green laser that I had mounted on my AR with a single mount. I found, with a single mount the laser moved during transport. The 3 slot rail I had was too short to mount two scope rings so I ordered this rail. Two rings fit perfectly and the laser is now quite ridged. This rail is made for the UTG Super Slim Free Float Handguard and my not work as well in other applications. I really love the Super Slim handguard, by the way. Oh, it comes with mounting screws and Allen wrench.

I bought this mount to use with a laser for my rifle. I wanted a strong detachable mount and this is it. When first receiving this mount I notice some wobble when the lever was in the tight position, then I noticed the Allen screw in the middle of the post, on which the lever is mounted,tightening this screw solved the issue. I think the addition of a drop of blue Loctite on the screw will keep it tight. I had to flip the mounts, one up one down when using in my particular installation because the mounts were so close together the lever of one mount would hit the one next to it. This would not be an issues on a scope. I liked the mount so well I bought a second pair for another rifle.

The rail Pictured is not the rail I ordered. The one I ordered is the next size longer. The rail pictured with two slots comes with the Handguard. I ordered the longer rail so I could use two Mounts to hold a Laser steady. Previously I was just using one Mount for the laser but found the laser would move ever so slightly, not aa issue with a flash light but big issue with a laser. With the longer rail I could attach to mounts and make the laser stable. The mount comes with screws and Allen Wrench.