Reviews & Ratings for CMMG, Inc A1 Stock Assembly — 11 reviews — Page 1

I would not recommend purchasing this for any AR platform unless it is airsoft.

I purchased this to replace an A2 stock on an old colt rifle of mine because I like the shorter length of pull. This product was fully functional, but disappointing. I honestly expected a lot more from CMMG. This stock is NOT a reproduction, but rather a cost-reduced look-alike. The is NOT foam core, but rather just hollow molded plastic. Theoretically gives more room inside, but it sounds hollow when I tap it. The main disappointment for me was the butt plate. The fit between the stock and the buttplate is poor with gaps and overhangs. Worst of all, the trap door is just molded plastic with a "living hinge" and a plastic snap closure that makes me think of Tupperware. I'm seriously reluctant to put anything inside because the door is so flimsy. I wanted to use my colt butt plate from my A2 stock on it, but the dimensions are so out of spec that it barely fits with poor alignment. I may be able carve on the stock with my Dremel until my mil-spec butt plate fits, but that may not work. I will keep this stock and use it, but if I could do over, I would buy a legit repro A1 stock from H&R (PSA) for just a little more money. On the plus side, my stock DID come with an A1 length screw. I bought one separately because I read that this stock did not come with one, so now I have a spare, I guess.

I used this as a replacement for my Calvary Arms A1 stock. The length of an A1, but with the styling of an A2 stock! Doesn't come with a screw, but since I replaced an A1 with an A1, I already had the screw.

Butt stock of very good quality, I have installed two others on rifles I have. Easy installation and function is great, if you want a stock shorter than the A2 this is a good option. Just don’t forget to order the installation screw for the A1 stock as well.

Just finished capping off my 6.5 grendel lower with this stock. Good stuff! I like the length better than the A2 and the install was a piece of cake. I've read some places that the buffer tube is impossible to remove? I took out the top butt-plate screw and it came right out. I *do* wish that they wouldn't put the buffer in the same bag as the stock without some kind of protection, the buffer and spring left a good bit of scratches on mine, but this rifle isn't going to be a show piece, so that's okay.

Very happy with this product. The stock is black and solid. I like the fact that it has A1 length but the look of an A2 stock. A1 was too long for me so I went this route and I love it. I have small arms and it feels great. I gave it 4 starts because it didn't came with the upper A1 Screw. I trusted the Q&A that someone said that it should come with a screw but mine didn't. It made me waste time on my build because of this. I had to go to another source to order it and would take another week. Other than that everything is great about the stock. Plastic door but I have seen duty rifles like that so no worries.

lightweight, solid, and the perfect length of pull for me. I'm 6'1" and have a ta31 ACOG on top of my build with a very short eye relief. my initial choice of stock was the newer hogue overmolded fixed rifle length stock. with the pad attached to the hogue, it was longer than an A2 stock. comfortable, but just too long for me or anyone of my friends who tried to shoot it. This A1 stock fixed all of my issues and did so in a smooth and classic way. very happy with my purchase.

The only gripe is that there is no kind of padding and there is a compartment for storage. I was under the impression the A2 stocks were the only ones with that feature.

the sling attachment point is solid and won't move on you. I out 500 rounds through my A4 yesterday and the stock performed better than expected.

Love this length stock. It should be noted though that although the description says A1 assembly, it does not include buffer tube, buffer, or spring. This is something to be aware of because sometime it can be a chore to locate A1 length buffer tubes.

A1 worked well on my 20" build. I had the longer length A2 stock and for some reason it felt a little long for the. The A1 fits just right although it it probably one setting longer than what I have on most of my collapsible stock setups I really prefer the solid stock setup. I started with a BCM 20" complete upper and then I found a bcm complete lower. I was originally going for an m16A2 build but again the a2 stock was too long for me. These A1 length stock have become harder and harder to find.