Your Browser is Outdated
Compare (0)
1 item has been added
Add at least two items to compare
Most Helpful Positive Review
Not as hard to install as some people think
To properly torque it you need to use a 1 1/8" crows foot wrench as per the instructions. Crows foot wrenches have a slot for a torque wrench. So torquing properly is not a problem.
I also had no problem with timing. All it takes is a bit of patience. The hand guard is a really tight fit over the n...
Read More...
Read More...
Most Helpful Negative Review
Not so great
Purchased this item for an easy replacement as advertised. What a nightmare!! First of all, my carbine is 100% Mil-Spec. Mounted plenty of mil-spec parts on it without a glitch. The rail is well made great quality and finish but it was impossible to put on. The instructions are not clear. So than...
Read More...
Read More...
Not V2. Listing is wrong
This listing is not the V2. I ordered it and the sent me the MCSR, not the MCSRV2. Very Disappointed and misleading
Would recommend: No
1 of 1 found the following review helpful.
It’s Solid AF!!
I bought this to replace a handguard that couldn’t seem to stay tight. Once this bad boy is installed it’s locked in. 8 t15 torx hold the tube to the barrel nut. The tube also has tight fingers that index it to the upper receiver rail. I’m very happy with this handguard, I have big hands so I appreciate the larger diameter of the tube. The tube diameter is larger 2.1” to accommodate a suppressor, I don’t have one but it doesn’t look out of place.
Pros:
- Solid, great design
Cons:
- None
Would recommend: Yes
Works with Aero M4E1 Enhanced upper
I bought this to fit over a planned suppressed 300BLK build. I'm a fan of the Aero Precision M4E1 Enhanced uppers, and figured it would work but couldn't find any specific info that this is compatible. This fits perfectly without needing or having to worry about timing the BAR barrel nut. And it looks great!
Would recommend: Yes
3 of 3 found the following review helpful.
Top Quality
As with all Seekins products the MCSR is a top of the line handguard. Not easy to find this so hats off to OP for digging one up.
Seekins gives a no questions asked, life time guarantee on all their products.
The last MCSR I purchased had a fitting issue, I let them know and they shipped out a new one the next day.
Seekins gives a no questions asked, life time guarantee on all their products.
The last MCSR I purchased had a fitting issue, I let them know and they shipped out a new one the next day.
Would recommend: Yes
1 of 1 found the following review helpful.
Perfect Rail
The best rail hands down to tuck my yhm resonator can inside of. Needed a new rail for my 300 bo w/8.5" barrel when my form 4 got approved. My options where limited but my previous experience with seekins made it a no brainer, and.i was not disappointed! Fit and finish are top notch and the barrel nut design is one of the easiest on the market.
Would recommend: Yes
Handgaurd Choice
Fit and finish was great. Barrel nut timing and tourqe was easy. Focus and double check your settings, no you can't slap it on and go !!! Will work with Adams Arms piston system XLT/P with a small amount of milling on the not to clear the rod and spring bushing. Locks up great on my 300blk setup. I don't care for super skinny handguards, plus plans in the future for a Tax Stamp.
Pros:
- Works as advertised.
Cons:
- You have to have a clue on what your doing.
Would recommend: Yes
2 of 2 found the following review helpful.
Good rail, TERRIBLE BARREL NUT
Good light strong rail, has anti rotation tabs, anti rotation qd mounts, and strong mounting to barrel but. But the barrel nut is some terrible 2 piece design thing, you have to time it for the gas tube, have to time it perfectly for the rail retention screws which requires the bigger but to be loose and not even close to the upper, then there's no way to torque the smaller barrel but cause it's a 3/4 inch hex but, had to use a crescent wrench and hoped it's tight enough. Beware.
Would recommend: No
4 of 7 found the following review helpful.
Mlok rail 15 inch
This is the perfect hand-guard for a bull barrel. It fit nicely over a JP adjustable .936 gas block. It looks great on the 16 inch bull barrel. One problem however, the barrel nut is too small for most bull barrels, considering this is a 1.8 inch inside diameter hand-guard I would think they would make the barrel nut larger to accommodate all barrels. It can be widened a variety of ways but the easiest solution would be for them to make the nut larger. It only needs to be widened to 1.05 from one inch. I used a small grinding attachment on a power drill to widen mine, took a few hours but when all is said is done I love this hand-guard.
Would recommend: Yes
0 of 1 found the following review helpful.
Great handgaurd, works with gas piston kits.
Great hand guard, put it on a 5.56 pistol with a gas piston kit. Rail fit perfectly over the piston gas block and easily accommodated the accessories I wanted to put on. Would recommend this hand guard to anybody.
Would recommend: Yes
Seekins MCSR M-LOK hand guard
Perfect fit on a Seekins upper. Light, smooth and comfortable. Placed mine on an 8 inch Seekins barrel with their adjustable gas block. My Silencerco Omega threads under this hard guard perfectly with about an inch of suppressor extending beyond the hand guard. Very smooth and very cool looking setup. Precision made.
Would recommend: Yes
1 of 1 found the following review helpful.
There are no reviews that match your criteria. Would you like to review this product?