by
max,
from CA, United States
Written on June 11, 2024
This ish right here got a pront sight post loose that I thought might have been welded onto my slide. Thank God for this thing.
Would recommend: Yes
0 of 0 found the following review helpful.
Was it helpful to you?
Yes
|
No
You said this review was not helpful.
Would you like to change your vote?
by
DaMan319,
Verified Owner
from IA, United States
Written on May 23, 2024
Works great. I only used it once. So haven't used it a lot but it works.
Would recommend: Yes
0 of 0 found the following review helpful.
Was it helpful to you?
Yes
|
No
You said this review was not helpful.
Would you like to change your vote?
by
Deejay,
from TN, United States
Written on March 28, 2024
Quality product, easy to use, fits front sight screw, easy to turn and secure
Would recommend: Yes
0 of 0 found the following review helpful.
Was it helpful to you?
Yes
|
No
You said this review was not helpful.
Would you like to change your vote?
by
Dale,
from AR, United States
Written on March 6, 2019
This front sight instillation tool is very easy to use to replace the front sight on my Glock pistols. The front sight is replaced in just a minute with no problems. This tool is a must have piece of equipment to add to your tool bag for going to the range or anywhere that you may need them without using an repair shop.
Would recommend: Yes
0 of 0 found the following review helpful.
Was it helpful to you?
Yes
|
No
You said this review was not helpful.
Would you like to change your vote?
by
Stew7968,
from CA, United States
Written on December 21, 2018
The Truglo forward sight removal tool worked ok, however the wall of the tool is a little thick a difficult to fit over the nut when it’s fully tightened. You have to work it at an angle until the nut is backed off enough for the tool to fit on it fully, from there it works ok.p
Would recommend: Yes
1 of 1 found the following review helpful.
Was it helpful to you?
Yes
|
No
You said this review was not helpful.
Would you like to change your vote?
by
Mac,
Verified Owner
from MI, United States
Written on August 6, 2018
There’s really not much to say about this tool. It’s used to remove the front sight on Glock pistols. It’s not complicated but needed because of the thin wall construction that’s required to capture the special hex screw on the underside on the Glock slide. The price won’t break the bank so get one rather than grinding down a socket to fit the screw. The rough textured grip is a plus.
Pros:
- Inexpensive
- Does what i expected it to do
Would recommend: Yes
0 of 0 found the following review helpful.
Was it helpful to you?
Yes
|
No
You said this review was not helpful.
Would you like to change your vote?
by
jimmybobjoe,
from VT, United States
Written on July 16, 2018
The hex has a dish shaped bevel on the end, which causes it to slip off the bolt, as the bolt head is very low profile. I had to grind the beveled end down with a dremel, so the hex fully engaged the bolt head.
Would recommend: No
2 of 2 found the following review helpful.
Was it helpful to you?
Yes
|
No
You said this review was not helpful.
Would you like to change your vote?
by
KDM,
Verified Owner
from VA, United States
Written on May 26, 2018
Worked like a charm, no complaints! Sometimes that low profile hex nut can be difficult to get a wrench on and this wrench makes short work of that. No doubt there are other great wrenches for front sights out there, but for the price this one is hard to beat.
Would recommend: Yes
0 of 1 found the following review helpful.
Was it helpful to you?
Yes
|
No
You said this review was not helpful.
Would you like to change your vote?
by
John,
from UT, United States
Written on May 23, 2018
Bought The tool for changing factory sights to night sights on Glock handguns. It worked perfectly on a Glock 29, and a Glock 21, it's a good tight fit, easy installation, shipping was fast, no complaints.
Would recommend: Yes
0 of 1 found the following review helpful.
Was it helpful to you?
Yes
|
No
You said this review was not helpful.
Would you like to change your vote?
by
Wheelspi,
Verified Owner
from NV, United States
Written on May 14, 2018
It’s a good tool and does the job. I just wish it was magnetic, would make it much easier to hold the screw. But good quality for the money. The magnet does magnet makes a difference tho. Like I said good quality for the price.
Would recommend: Yes
0 of 1 found the following review helpful.
Was it helpful to you?
Yes
|
No
You said this review was not helpful.
Would you like to change your vote?