Reviews & Ratings for Wheeler Fine Gunsmith Equipment Delta Series Variant Receiver Lapping Tool AR LR/10

Wheeler Fine Gunsmith Equipment Delta Series Variant Receiver Lapping Tool AR LR/10

List: $58.59 $42.19 Save 28%

Write a Review

Compare (0)

Most Helpful Positive Review Wheeler Receiver Lapping Tool AR LR/10

I ALREADY OWN THE WHEELER AR/15 LAPPING TOOL. I AM NOW BUILDING SEVERAL AR/10's. BECAUSE THESE COMPANIES ARE TURNING OUT UPPERS LIKE POPCORN, SOME OF THE UPPER RECEIVER BARREL SURFACES ARE AS MUCH AS 0.005+ (THOUSANDTHS) CANTED EITHER LEFT, RIGHT, UP OR DOWN. THIS CAN CAUSE ERRATIC BULLET IMPACT AS ...
Read More...

Most Helpful Negative Review Poor quality and improper handling.

Tool arrived with scuffs, dings, and the receiver shaft has a small ridge that runs its length, tool/not round. Even after removing the burs cleaning up the dings and lubricating liberally, the out of round shaft scared the interior of my upper where the bolt resides. The tool was properly packaged...
Read More...

Show

Sort by

Filter by

Was not true

by Jim, Verified Owner from MO, United States Written on December 26, 2024

Threw mine in the lathe to square off the giant chamfer on the working face of this tool that really shouldn't be there and it wasn't even true. Very disappointing. I should have just made my own.

Pros:

None

Cons:

Better off making it out of a stick in the woods with nothing but a rock

Best Used for:

Paperweight

Was it helpful to you? Yes | No

doesnt fit

by Seth, Verified Owner from TX, United States Written on December 1, 2024

Don’t waste your time with this… they didn’t increase the size of the cutting head to accommodate AR10 barrel extensions so it will not cut the entire surface… Idk how anyone at Wheeler could have approved this but they need to find new people

Pros:

NONE !

Cons:

doesnt work

0 of 1 found the following review helpful.

Was it helpful to you? Yes | No

Highly effective

by Sgt.Brad, Verified Owner from OH, United States Written on October 15, 2024

In just a short period of time, this tool let's you alleviate one possible inconsistency. Shots were more consistent after truing the face of the receiver.

1 of 1 found the following review helpful.

Was it helpful to you? Yes | No

laps great BUT!

by drcmcico, Verified Owner from OH, United States Written on September 18, 2024

Says it’d work for an AR-10 but the diameter isnt round enough for an Aero Precision upper. It leaves about a 1/16th” metal ring that it didn’t lap off.

Pros:

worked great for 25 months

Cons:

None

Was it helpful to you? Yes | No

Not built right - avoid

by Jim, Verified Owner from OR, United States Written on July 31, 2024

The concept of the lapping tool sounds good. I do see how the mating face of my AR10 upper could affect accuracy which lapping would "True" the alignment to the BCG and barrel extension, which seems like it couldnt hurt to squeeze out a little more accuracy. However this Lapping tool is poorly built and executed. The lapping face of the tool is too narrow and doesnt go to the outer edge of the upper mating face. It is also poorly machined and has a "grooved" face which put round/circular depressions in the mating face of my upper. If I hadnt caught it soon enought it could have ruined my upper all together. I would avoid or buy a better quality lapping tool from an other manufacturer.

Pros:

None

Cons:

everything

Best Used for:

Not buying

Was it helpful to you? Yes | No

almost ruined my upper

by ejams, Verified Owner from IN, United States Written on July 14, 2024

The lapping face of the tool is too small and has a chamfer on the edge. That chamfer began to grind a conical gouge into my receiver and almost ruined it before I caught it.

Pros:

Black and thick.

Cons:

Heavy

Best Used for:

Clubbing small animals
if you're brave enough

Was it helpful to you? Yes | No

Well Made Product

by Jon, from OK, United States Written on July 29, 2020

Excellent tool and very easy to use. Lapping can be done without using the drill adapter. You only need to remove a few millimeters to square the barrel mating surface. The only issue is the package had been opened and everything was rattling around in the box. Doesn’t appear to be damaged. -2 stars for selling an open package.

Pros:

None

Cons:

Open package

1 of 1 found the following review helpful.

Was it helpful to you? Yes | No

Worth the money

by DPS, Verified Owner from TX, United States Written on June 26, 2020

Just a bit of oil on the main journal and then the cutting compound on the larger one (just follow the instructions) and in a few seconds of use, you are good to go.

Very easy to use and a good value for the money. I'd expect getting dozens, if not many multiples of that, uses out of the amount of compound they send you alone. If properly stored, I can see the tool itself lasting forever.

Pros:

Value an quality

Cons:

None

3 of 3 found the following review helpful.

Was it helpful to you? Yes | No

Wheeler 308 Lapping Tool

by Joe, Verified Owner from CA, United States Written on May 4, 2018

I bought this to use on a AR 308 build to make sure the surfaces were straight and true. It was easy to use and did its job without an issue. The flexible attachment for a hand drill was useful as well. You could make the same tool using a lathe but for those who don't, the price of this tool is just right.

Pros:

easy to use

Cons:

None

Was it helpful to you? Yes | No

There are no reviews that match your criteria. Would you like to review this product?

FREE SHIPPING on Over 250,000 Products

Enjoy our FREE RETURNS

Reviews & Ratings for Wheeler Fine Gunsmith Equipment Delta Series Variant Receiver Lapping Tool AR LR/10 — 11 reviews — Page 1