Your Browser is Outdated
Compare (0)
1 item has been added
Add at least two items to compare
Most Helpful Positive Review
Nice Hand Guard
Fits well on to WC receiver, looks good, no apparent defects. The only complaint is that WC does not supply a wrench, unlike other manufacturers who do provide a wrench with their hand guard. So, add the cost of a WC wrench to the total cost of the hand guard.
Most Helpful Negative Review
wilson combat hardguard
Was not the same as the picture description. The screw sets were below the picture. The screws aren’t flat so it’s exposed. Still lightweight and it does the job as intended. But when you buy something you want it to be as it shows as the description
Nice Forend
Fit and finish are perfect. Make sure you have a 30 mm crowfoot wrench to torque the barrel nut. Great instruction paper provided by Wilson. Perfect match for my Wilson 20” Super Sniper Barrel.
Would recommend: Yes
Wilson Combat Handguard
Put on my 13.7" build, and it looks great. The screws to keep in place were a little tricky. They didnt really want to go in. Very well could have been operator error or just an odd angle to screw in to. The barrel nut also took some elbow grease to have it be lined up with the screw holes in the handguard.When sliding the handguard on required some lube, it was a very tight fit which is also a good thing. Seems very durable, no wiggle room, tight fit, but requires little more work than the usual screw on barrel nut and tighten it together
Pros:
- durable
- tight-fit
Cons:
- None
Would recommend: Yes
Beautiful part. Fit and Finish is what I wanted.
This part exceeded my expectations. Fit and finish was perfect and looks great installed. Highly recommended. Shipping and communications were great!
Would recommend: Yes
Wilson Hanguard
Fit and finish as expected from WC. I have a ported (top and sides) compensator and the 15in hand-guard stops right at the ports so works for my setup.
Pros:
- Good looks and fitment
Cons:
- None
Would recommend: Yes
Quality is there
Very tight fit, simple install. Look and feel is good haven’t taken it out yet but so far so good.
Would recommend: Yes
Wilson Combat Rail on 18” SPR
Solid rail on my SPR build. Very sturdy, lots of room for accessories.
Would recommend: Yes
Tight w/extra$
Bought this handguard to go with my Wilson barrel. As with other reviews I found 'slipping' handguard over barrel nut next impossible without using force. I gave up quickly because I did not wish to damage handguard. Also it would have been very difficult to line up upper picatinny rails with handguard. Finally, the finish was very thin. In fact, it was rubbed bare in high spots out of package.
With all this and no information about barrel nut size and having to purchase armorer's wrench separately I decided to return handguard. I purchased another handguard kit that came with armorer's wrench and is easier to fit over barrel nut.
Optics Planet representative was big help with this return. Thank You!
With all this and no information about barrel nut size and having to purchase armorer's wrench separately I decided to return handguard. I purchased another handguard kit that came with armorer's wrench and is easier to fit over barrel nut.
Optics Planet representative was big help with this return. Thank You!
Would recommend: No
Favorite Handguard
The Wilson Combat M-Lok Handguards are my personal favorite.
They're smooth along the sides, and do not rough up your hands when not using gloves.
I also like the way they attach to the barrel nut and not rely on a clamping force to keep it steady.
They're smooth along the sides, and do not rough up your hands when not using gloves.
I also like the way they attach to the barrel nut and not rely on a clamping force to keep it steady.
Pros:
- Attaches directly to Barrel Nut
Cons:
- May require timing barrel nut with shims
Would recommend: Yes
0 of 1 found the following review helpful.
There are no reviews that match your criteria. Would you like to review this product?