by
tom,
Verified Owner
from TX, United States
Written on May 9, 2024
I used this on my Harris s and works great. Took just a few minutes
Would recommend: Yes
0 of 0 found the following review helpful.
Was it helpful to you?
Yes
|
No
You said this review was not helpful.
Would you like to change your vote?
by
AMGtuned,
Verified Owner
from ME, United States
Written on March 25, 2019
Bought this for a Harris sbrm bipod. Nothing was clear if it had the same attachment as for the Harris. It does! Installation was a breeze and the unit works great. Locks the bipod down tight and the reset mechanism functions well. Only reason for 4 stars; made from polymer of some sort, I would've preferred aluminum
Pros:
- Mounts to Harris, long arm provides leverage
Cons:
- Polymer not steel or aluminum
Would recommend: Yes
0 of 0 found the following review helpful.
Was it helpful to you?
Yes
|
No
You said this review was not helpful.
Would you like to change your vote?
by
Bill,
Verified Owner
from OK, United States
Written on July 29, 2018
It's a nice upgrade to the Factory thumb screw. I used this on a Harris S the lever is made out of a polymer but it feels very solid. It's so much faster to lock the bipod in position than the thumb screw its also easy on the finger's. Money well spent.
Pros:
- Faster than the thumb screw.
Would recommend: Yes
0 of 0 found the following review helpful.
Was it helpful to you?
Yes
|
No
You said this review was not helpful.
Would you like to change your vote?
by
Kroger,
from IA, United States
Written on October 5, 2017
I was expecting a simpler install for this type of item. Turns out, a 5/16” socket wrench and 2.5mm hex key wrench are required and not included. However, fit and finish of the product are good for the price. For that reason, I still gave it four stars.
Would recommend: No
0 of 1 found the following review helpful.
Was it helpful to you?
Yes
|
No
You said this review was not helpful.
Would you like to change your vote?
by
Ace 53,
from OR, United States
Written on June 15, 2017
The bang for your buck that you get with this makes it a no brainer if your harris bipod lacks some sort of tension adjustment arm. If you ever shoot off uneven ground, being able to quickly confirm your rifle is level before taking the shot is key. This simple and reasonably priced decides allows this to occur.
Would recommend: Yes
1 of 1 found the following review helpful.
Was it helpful to you?
Yes
|
No
You said this review was not helpful.
Would you like to change your vote?
by
SniperCat,
from FL, United States
Written on May 1, 2017
A friend introduced me to this product. It's a great idea because using the pivot lock handle instead of trying to move the nut with your fingers is so much easier. The only problem is. In the directions. They say to use a 5/16" socket. The nut is actually a 1/4". I drove me crazy for about 10 minutes!
Would recommend: Yes
0 of 0 found the following review helpful.
Was it helpful to you?
Yes
|
No
You said this review was not helpful.
Would you like to change your vote?
by
Minuteman,
Verified Owner
from MA, United States
Written on October 20, 2016
As my experience shooting at extreme long range increased, I became aware of the importance of keeping the rifle level at all times. I put a bubble level on my rifle but was frustrated by the difficulty of adjusting the rifle tilt when on uneven ground. This gadget is the answer. It allows instant adjustment and then locks up solid. Easy to install. Lightweight. Highly recommended.
Would recommend: Yes
0 of 0 found the following review helpful.
Was it helpful to you?
Yes
|
No
You said this review was not helpful.
Would you like to change your vote?