Your Browser is Outdated
Compare (0)
1 item has been added
Add at least two items to compare
Most Helpful Positive Review
Great cheap rmr/holosun Mount
As advertised. It is very slim and light and sturdy. The 3 lugs make it interface very well in picatinny. I had no problem with it fitting on multiple different pic bases. It is very high quality for price. Usually UTG has had a bad rep for cheap stuff, but this is very nice mount. The only issue I ...
Read More...
Read More...
Most Helpful Negative Review
Didn’t work for me
Not as low profile as the trijicon low profile mount. Also the mount itself wouldn’t really secure down on the rail of a ruger mark iv 22/45 lite. For the price it does seem pretty well built but skip it if trying to put on a ruger mark iv rail.
Tight tolerances
For the price this mount is good. My only issue was how thigh the tolerances were on the 1913 pic rail section. I was using it to top mount a RMR style red dot to a Burris AR-P.E.P.R Rifle Scope Mount and the couldn't get the teeth of the pic rail to slide into one another. A little love from a gunsmith rubber mallet finally got the two pieces to seat. After that mounting the dot and torquing every thing down was a breeze. The RMR style dot mounted solid and so far no shift in zero.
Pros:
- solid
Cons:
- Tight tolerances
Best Used for:
- All uses
Would recommend: Yes
rmr mount review
I have a holosun pistol dot mounted to a carry handle using this mount. It works as advertised. No issues.
Would recommend: Yes
It does the job.
Not a lot to say about this type of product. It either fits or doesn't fit.
It mounted fine. I use thread-lock. The optic mounted straight & flush, as it should. I zeroed the optic using a laser at 50 yards.
Went to the range, shot off a few boxes. I checked the mount and the zero when I got home. All perfect.
Although my thoughts on inexpensive gun parts tend to be just that, the Leapers mount seems to work exactly as described.
I'll purchase another few, just to keep on hand for my next project(s).
It mounted fine. I use thread-lock. The optic mounted straight & flush, as it should. I zeroed the optic using a laser at 50 yards.
Went to the range, shot off a few boxes. I checked the mount and the zero when I got home. All perfect.
Although my thoughts on inexpensive gun parts tend to be just that, the Leapers mount seems to work exactly as described.
I'll purchase another few, just to keep on hand for my next project(s).
Would recommend: Yes
Great product !
The only draw back is that it only comes with long mounting screws , I wish it came with some short ones too . I had to trim the long screws to work right .
Pros:
- good quality
Cons:
- Only came with long screws
Would recommend: Yes
pic rail mount
I bought this to mount a swampfox RMR optic on my Mossberg 500. It locks down solid and fits the optic perfectly!!
Would recommend: Yes
looks good
Bought this to mount an rmr on the ruger mark iv ssh while waiting for an aftermarket optic plate. Didn't fit the picatinny rail on the ruger but fit on any other picatinny upper I had. Might hold onto it anyway.
Would recommend: Yes
low profile rmr mount
This is a solid mount. I ussd it to mount a Holosun 507C on my Mossberg 930. It was easy to install and is firmly in place on the picatinny rail. It's pretty good quality for the price. OpticsPlanet shipped it to me fast and I couldn't be happier with my purchase. I would definitely buy it again.
Pros:
- Easy to mount
- East install
- priced affordable for such quality
Cons:
- None for me
Best Used for:
- mounting a rmr footprint optic
Would recommend: Yes
RMR Picatinny mount
I put a Holosun 407C on my 22 LR lever action. Fit and finish is perfect. Aids in getting on target quickly.
Pros:
- EASY INSTALL
Cons:
- Non that i have found yet
Best Used for:
- Red dot mounting
Would recommend: Yes
Great Value Mount
I used this mount to put a holosun 407 on top of a primary arms 5x prism scope. Its a fairly tall optic height, so I wish this mount was slightly lower profile. But overall great fit and finish and cant beat the price. I love that they use torx head screws and not allen heads. Im very happy with this mount so far.
Would recommend: Yes
2 of 2 found the following review helpful.
There are no reviews that match your criteria. Would you like to review this product?