TRYBE Defense AR-15 Curved Drop-In Trigger

Your loyal friends at TRYBE have your back again with some new gear. Check out the high-performance TRYBE Defense AR-15 Curved Drop-In Trigger to improve your shot control while hunting, range training or match shooting. These single stage Rifle Triggers developed by the innovators at TRYBE Defense offer an adjustable pull weight of 3.5 - 5 lb so that you can customize your pull force precisely to your preference. The TRYBE Defense AR-15 Curved Drop-In Rifle Trigger is housed in anodized aluminum, and the components are crafted from nitride heat treated steel to ensure that the entire trigger assembly is ultra-durable and resistant to corrosion and abrasion. Pick up the TRYBE Defense AR-15 Curved Drop-In Trigger w/ Anti-Walk Pins for smooth, precise shots with every pull.

Got your eye on some new gear, do ya? Don't sleep on all the amazing firearms accessories and tactical gear that TRYBE has to offer for your next build, or just to give yourself an edge in the field. TRYBE Defense has all of the AR Parts you need to keep your rifle looking fierce and operating at a high level, including a huge variety of M-LOK Cut-Rail & Full-Rail Handguards and Upper Receivers. But don't stop there with your AR build. Feast your eyes on all the other high-quality parts and accessories the innovators at TRYBE Defense have to offer. From fully assembled Bolt Carrier Groups and ambidextrous Charging Handles and Safety Selectors to high-performance adjustable Drop-In Triggers and ultra-effective Muzzle Devices. And our hyper-accurate, long-lasting Rifle Barrels and durable Grips & Handstops will keep those groupings tight!

And for the muzzle brake with industry-leading recoil reduction, by partnership with Alamo Four Star, the TRYBE Defense Cowl Induction Muzzle Brake is back in all its signature suppressing glory. Muzzle rise and propellant gases are massively diminished thanks to ingenious engineering and high-quality materials. Check out this very scientific video to see for yourself the capabilities of this CIB. And don't forget to wipe the drool off your chin.

But you're going to need something to carry all that swag. Finish it off with a TRYBE Tactical 42" Rifle Case or TRYBE Tactical 28" SBR Case to wrap your rifle in soft, cushy protection. If you're toting a load of gear, the spacious TRYBE Tactical Range Bag has all of the right pockets to keep you well supplied and organized.

For other quality gear to carry and protect everything you'd need for a day at the range check out the premium field accessories that your loyal friends at TRYBE Tactical and TRYBE Optics have for you. Start customizing today and get ready to JOIN. THE. TRYBE.

How to Install Your New Drop-In Trigger

NOTE: FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS CAN RESULT IN MALFUNCTION OF THE TRIGGER

Note: Always wear eye protection; parts are spring-loaded!

1. Remove the magazine & verify the chamber is empty to ensure the firearm is unloaded.

2. Unlock the pivot and rear lug pins, remove the upper receiver from the lower receiver and set it aside.

3. Carefully decock the hammer.

4. Use a punch and small hammer to drive out the hammer and trigger pins. remove the hammer.

5. Loosen the grip screw from inside the grip to allow the grip to drop about 1/2 inch. Be careful not to lose the SAFETY DETENT SPRING, or the DETENT PIN.

6. Slide the safety out of the receiver and remove the trigger.

7. Insert the drop in trigger assembly into the lower receiver.

8. Install the hammer and trigger pin, or anti-walk-pins (optional)

Do not over tighten anti-walk-pin screws.

9. Re-seat the safety selector.

10. Re-align grip, safety detent pin, and spring, then tighten the grip screw.

11. Tighten both set screws on both sides of the drop-in-trigger until it is seated.

12. Function test your new trigger to ensure the trigger works as it should.

TO ADJUST THE TRIGGER PULL WEIGHT:

Carefully release the hammer if cocked. Use an allen wrench to turn the set screw on top of the trigger by a 1/4 turn, counter-clockwise to decrease the trigger pull weight, or clockwise to increase the pull weight. test your trigger, repeat if necessary.

CAUTION: DO NOT LOOSEN THE SET SCREW ALL THE WAY OUT.

Features of TRYBE Defense AR-15 Curved Drop-In Trigger

• Anodized 6061-T6 Aluminum Housing
• Heat Treated, Polished, Nitride Finished AISI 8620 Alloy Steel Components
• Adjustable Pull Weight of 3.5 - 5 lb
• Anti-Walk Pins Included
• Easy to Install
• Supremely Crisp Trigger Pull
• Laser Engraved TRYBE Eagle Logo

Package Contents:

• TRYBE Defense AR-15 Curved Drop-In Trigger
• Anti-Walk Pins
• Installation Manual

Similar Products to TRYBE Defense AR-15 Curved Drop-In Triggers

• TRYBE Defense Cowl Induction Muzzle Brakes
• TRYBE Defense AR Parts
• TRYBE Defense M-LOK Cut-Rail & Full-Rail Handguards
• TRYBE Defense Upper Receivers
• TRYBE Defense Bolt Carrier Groups
• TRYBE Defense Charging Handles
• TRYBE Defense Safety Selectors
• TRYBE Defense Drop-In Triggers
• TRYBE Defense Muzzle Devices
• TRYBE Defense Rifle Barrels
• TRYBE Defense Grips & Handstops
• TRYBE Tactical 42" Rifle Case
• TRYBE Tactical 28" SBR Case
• TRYBE Tactical Range Bag
• TRYBE Tactical
• TRYBE Optics

TRYBE Warranty

TRYBE™ products are made for performance and durability and are covered by a comprehensive warranty depending on the type of product. See full warranty information here

Which weapon models is TRYBE Defense AR-15 Curved Drop-In Trigger compatible with?